Fluid Bed Dryer

This compact unit is suitable for drying granular, crystalline, coarse or similar materials in Pharmaceuticals, Dryer, Fine Chemicals & Food & Allied Industries. It is also possible to dry fine crystal or coarse materials in fluid bed dryers.

We manufacture Batch wise Fluid Bed Dryer with capacity 30,60,12,200,250,250,500 Kgs and also Lab Model .

The wet material is introduced into the dryer as a batch of material in a product container which is provided with air distributor plate & clutch weave. Induced draught is created by the blower & fresh air is sucked into the unit. After filteration, clean air passes through the heating elements. This hot air then passes through the product containers, creating turbulance in the products & hence the product moves up and down known as Fluidization in the product container. Due to this process, the heat transfer is quick and the product is dried fast without appreciable loss of heat. Filter bags prevent particles escaping from the dryer.

Fluid Bed Dryer can be supplied in electric heating, steam heating or hot water circulation systems or gas heating system on demand. Electrically heated dryers are provided with electrical heating elements and are suitable to raise air temperatures by about 750 C (i.e from 300 C to 750 C). Similarly steam operated dryers are provided with steam radiator suitable to raise air temperature about 600 C to 750 C depending upon pressure of steam. Generally dryers bigger than RDFD- 60 are incorporated with steam heating system as it is more economical.

The drying time depends upon various factors such as physical properties of material, moisture content, type of moisture (free moisture or water of crystallization), drying temperature etc. The crystalline products can be dried faster than amorphous product containing same percentage of moisture at the same temperature. Generally pharmaceutical granules or crystals containing free moisture of about 20% to 25% can be easily dried in about 30 to 40 minutes at a temperature of about 750C. Certain crystalline materials containing about 40% of moisture can be dried in Fluid Bed Dryer within 35 to 45 minutes.

The dryer will be provided with with suitable Remi/Hindustan/Sabar or standard ISI make motor of 2800 RPM.

Single stage filteration of 20 microns PP cloth filter, P.P. filter bag for exhaust air, also multi stage filteration can be given on demand. Positive Earthing Arrangement, explosion flap are given as a part of standard features.

20 Micron Pre filter, 5 Micron, 0.3 Micron Hepa Filter with either electrical heating or steam heating.

Pre-wired control panel indicate Digital Timer, Digital Temperature Indicator cum controller(Inlet), Digital Temp. Indicator (Outlet), Sensor, Star-Delta Starter with relay, Indicating Lamps, MCBs, Amp. Meter cum Volt Meter, Selector switch etc.

Or PLC HMI based control panel with Scada, 12 CFR compliant Part 11.

1.) Uniformity in drying and reduction in drying time.
2.) Air suction and discharge dampers provided to control the inlet and outlet air flow.
3.) Timer provided to set the process time which will cut off the motor supply after pre-set time period.
4.) Atmospheric inlet air is filtered by means of single / multi stage filters of 20 microns to prevent any fine dust to pass through the product.
5.) Steam Coil made out of 1” dia. SS 304/316 finned tube & is designed to get pressure of around 3-4kg./cm^2 (working pressure 3 kg/cm^2).
6.) Digital temperature indicators cum controller is provided with the unit to indicate the inlet and outlet air temperature as well as to controller the present inlet air temperature.
7.) An explosion safety flap of adequate capacity at the rear end of the dryer and an positive earthing point to prevent static charge in the machine are provided.

1.) Level floor at site.
2.) Electrician at the time of Installation.
3.) Ducting from exhaust to the wall with fittings.
4.) 4 sq.mm 6 core wire from panel Board to main motor.
5.) 1.5 sq. mm 2 core wire from panel Board to Pneumatic section.
6.) 0.5 mm 3 core wire from Panel Board to inlet & out let sensor.
7.) Proper floor pan to be given at the time of ordering the machine.
8.) 3 phase power supply upto the control panel of the machine.
9.) Compressor with FRL to supply pure air to the Pneumatic components.
10.) Required electrical connection up to the machine through suitable isolating switch.
11.) Steam boiler and all the connections, fittings and pipe, with controllers and pressure gauges to be connected to the radiator by party.
12.) Inlet steam & outlet steam line with pressure gauge safety valve, by pass, On & Off Gate Valve provision to be made, electrical operated steam control valve 1 inch or ¾ inch BSP to be given.